COP iLink Status and Remote Command List

A Internal Command list For app_rpt (incomplete)
More is added from time to time. Some,not all default assignments shown.

An important note that I’m going to repeat for those that stumbled on this page without having read the others:

It is important to “organize” your commands so that you do not partially “dupe” a command.

I suggest keeping them in numerical order so it can be easily seen. Here is a example:

8900=cop,24   ; cancel localplay stream +/- telemetry

8901=localplay,/var/lib/asterisk/sounds/wx/wxfc    ;my custom wx script player example

8902=localplay,/var/lib/asterisk/sounds/wx/wxalert    ;my custom wx alert script player example

90=cop,1          ;warm boot
91=cop,2           ; System enable – you should not comment these out in a live system
92=cop,3        ; System disable

99=cop,6          ; Remote sip/telephone PTT key command  (# to unkey)

If I were to assign a command of *89 to anything, the above 4 digit 8901, 8902 would never execute. Unlike conventional controllers, asterisk will run with and execute the first match it gets.  So if there were a command created for *89,  *89 would always execute and” never ” execute a 3 or four digit command starting with *89.

So if you find yourself in this dilemma, make all *89 commands 3 or 4 digit commands to avoid it. Keeping them in order on your command list helps avoid the problem in the first place.

Saying that,  here is my list of assignable commands I have compiled over time.

Status Commands

80=status,1       ; Force id global
81=status,2       ; Time
82=status,3       ; Give Software ver Global

=status,11   ; Force ID (local only)
=status,12   ; Give Time of Day (local only)

87=status,15    ; global node query (reads back all nodes connected in the network

iLink Commands

=ilink,1 – Disconnect specified link
=ilink,2 – Connect specified link — monitor only
=ilink,3 – Connect specified link — transceive
=ilink,4 – Enter command mode on specified link

70=ilink,5        ; Link Status (long)
71=ilink,6        ; Disconnect All Links
72=ilink,7
75=ilink,8

=ilink,11 – Disconnect a previously permanently connected link
=ilink,12 – Permanently connect specified link — monitor only
=ilink,13 – Permanently connect specified link — transceive

73=ilink,15       ; Full Sys Status (all nodes)
74=ilink,16       ; Reconnect Links (that were disconnected by command)

=ilink,200 thru 215 – (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)

Control Operator ( COP ) Commands
Keep in mind, some commands only valid under certain configurations.

=cop,1       ;warm boot
=cop,2       ; System enable
=cop,3       ; System disable
=cop,4        ; Test tone on/off – or # to end
=cop,5        ; Dump system variables on console (debug use only)
=cop,6          ; Remote base telephone tx cntl key
=cop,7        ; Time out timer enable
=cop,8        ; Time out timer disable
=cop,9        ; Autopatch enable
=cop,10        ; Autopatch disable
=cop,11        ; User linking functions enable
=cop,12            ; User linking functions disable
=cop,13        ; Query system control state
=cop,14        ; Set system control state
=cop,15        ; Scheduler enable
=cop,16        ; Scheduler disable
=cop,17        ; User functions enable (time, id, etc)
=cop,18        ; User functions disable
=cop,19        ; Select alternate hang time (althangtime)
=cop,20        ; Select standard hangtime (hangtime)
=cop,21     ; Enable Parrot
=cop,22     ; Disable Parrot
=cop,23     ; Bird Bath – Clean Residual stream  -also see cop 55
=cop,24     ; flush all pending telemetry in the buffer
=cop,25 ; return last node which unkeyed from any connected node (directly or indirectly)
=cop,26 ; Query all nodes which keyed or unkeyed from any connected node (directly or indirectly)

=cop,27   ; Reset DAQ minimum on a pin
=cop,28   ; Reset DAQ maximum on a pin
=cop,30   ; Recall Memory Setting in Attached Xcvr
=cop,31   ; Channel Selector for Parallel Programmed Xcvr

=cop,32     ; DTMF Pad test – end with #
=cop,33     ; Local Telemetry Output Enable
=cop,34     ; Local Telemetry Output Disable
=cop,35     ; Local Telemetry Output on demand

=cop,36     ; Foreign Link Local Output Path Enable
=cop,37     ; Foreign Link Local Output Path Disable
=cop,38     ; Foreign Link Local Output Path Follows Local Telemetry Selection (above)
=cop,39     ; Foreign Link Local Output Path Timed

=cop,40     ; IRLP announce Enable
=cop,41     ; IRLP announce Disable
=cop,42     ; Echolink announce node # only
=cop,43     ; Echolink announce node Callsign only
=cop,44     ; Echolink announce node # & Callsign
=cop,45     ; Link Activity timer enable        -LATENA
=cop,46     ; Link Activity timer disable        -LATDIS
=cop,47 ; Reset”Link Config Changed”Flag -none -change link state without arming activity timer

=cop,48 – Send Page Tone (Tone specs separated by parenthesis)
=cop,49 – Disable incoming connections (control state noice)
=cop,50 – Enable incoming connections (control state noicd)

=cop,51  ; Enable Sleep Mode
=cop,52  ; Disable Sleep Mode
=cop,53  ; Awaken from Sleep
=cop,54  ; Go back to sleep when the TX carrier drops
=cop,55     ; Parrot Once Command
=cop,58        ;Tx CTCSS On Input only Enable (also see itxctcss=1)
=cop,59        ;Tx CTCSS On Input only Disable

=cop,61,pp3=0 ; parallel port control: pp+pin number + 0 or 1 for on/off

=cop,80     ; Change Default Squelch Code (Xelatec)

Remote Base – default assignments shown

0=remote,1          ; Retrieve Memory
1=remote,2          ; Set freq.
2=remote,3          ; Set tx PL tone
3=remote,4          ; Set rx PL tone
40=remote,100       ; Rx PL off
41=remote,101       ; Rx PL on
42=remote,102       ; Tx PL off
43=remote,103       ; Tx PL on
44=remote,104       ; Low Power
45=remote,105       ; Medium Power
46=remote,106       ; High Power
711=remote,107      ; Bump -20
714=remote,108      ; Bump -100
717=remote,109      ; Bump -500
713=remote,110      ; Bump +20
716=remote,111      ; Bump +100
719=remote,112      ; Bump +500
721=remote,113      ; Scan – slow
724=remote,114      ; Scan – quick
727=remote,115      ; Scan – fast
723=remote,116      ; Scan + slow
726=remote,117      ; Scan + quick
729=remote,118      ; Scan + fast
79=remote,119       ; Tune (brief AM transmission for automatic antenna tuner)
51=remote,5         ; Long status query
52=remote,140        ; Short status query
67=remote,210       ; Send a *
69=remote,211       ; Send a #

91=remote,99,CALLSIGN,LICENSETAG
; Remote base login.
; Define a different dtmf sequence for each user which is
; authorized to use the remote base to control access to it.
; For examble 9139583=remote,99,WB6NIL,G would grant access to
; the remote base and announce WB6NIL as being logged in.
; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to
; the remote base and announce WA6ZFT as being logged in.
; When the remote base is disconnected from the originating node, the
; user will be logged out. The LICENSETAG argument is used to enforce
; tx frequency limits. See [txlimits] below.

200 thru 215 – (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)

Other

Here is handy command to run any script calling system commands that you can later call from a macro/scheduler.

XXX=cmd,/some/were/in/your/filesystem.sh  ;example to call a script by dtmf command